Evdə və iş yerində ehtiyaclarınıza uyğun internet xidmətləri təqdim edirik.
Yüksək sürətli fiber-optik internet bağlantısı ilə ailəniz və eviniz üçün sürətli və etibarlı internet xidməti.
Şirkətiniz üçün yüksək keyfiyyətli, etibarlı və genişzolaqlı internet həlləri. 24/7 texniki dəstək xidməti.
Mövcud internet sürətinizi ölçmək üçün sürət testindən istifadə edin.
Aşağıdakı düyməni klikləyərək cari internet bağlantınızın yükləmə və endirmə sürətlərini ölçə bilərsiniz.
To help you get the most out of your setup, what is the (e.g., 2kW, 3kW, or 4kW), and what are the busy peak hours for hot water in your household? Share public link
Provides a 1-hour manual bypass to heat water instantly. Note that this override is typically disabled during designated peak load times to prevent grid strain. LED Status Lights: Green: Mains power is connected. Red: Geyser is currently ON .
Disclaimer: High-voltage work can be dangerous. Installation must be performed by a qualified electrician or under strict safety guidelines. Always switch off the main DB power supply first. Prerequisites KES ISG1201 Go to product viewer dialog for this item. Timer Unit Flat screwdriver Appropriate wire cutters/strippers DIN Rail space in the DB Board
If your geyser element exceeds 4000W or the timer’s rated current limit, install a heavy-duty electrical contactor alongside the timer. The timer will switch the contactor coil, and the contactor will safely handle the high current load of the geyser. Troubleshooting Common Issues
If you need water urgently, use the manual override outside of peak hours. For long-term savings, ensure your geyser thermostat is set between 55°C and 60°C .
Press the MANUAL override button until the screen explicitly reads . Schedules trigger at the wrong times
Toggles the operational state between permanent ON, permanent OFF, or scheduled AUTO modes.
Snap the KES timer securely onto the DIN rail and close the distribution board safety panel. 3. Interface Overview and Button Functions
This guide serves as a manual for the "Kes geyser load control timer new," offering a detailed breakdown of its features, programming, installation, and troubleshooting to ensure you can harness its full potential.
Nina smiled. She taped the inside the meter box, right next to the silent, obedient unit.
Press the button to adjust the exact minute for activation. Programming Schedule 1 (OFF Cycle)
Always switch off the main electrical supply at the circuit breaker before touching any wiring. Verify the power is off using a reliable voltage tester.
Connect the incoming from the main neutral bar to Terminal 2 (Input N) on the timer.
While holding the Clock button, press to adjust the current hour.
Verify that the screen displays the word AUTO . Press P to check your schedules and confirm that the days selected for "1_ON" are identical to the days selected for "1_OFF" .
Once your schedules are entered, press the button to save and exit to the main screen. How to Modify or Delete a Single Program
Connect a wire from on the timer to the neutral input side of the geyser isolator switch.
The KES ISG1201 includes four factory-set profiles. To select a program, use the button to cycle through them. Blue LED Pattern Function & Operating Hours Prog 1 1 flash / second
X-link şəbəkəsinin cari işləmə vəziyyəti və planlaşdırılmış texniki işlər haqqında məlumat əldə edin.
Son yeniləmə: 08 May 2026, 22:05
To help you get the most out of your setup, what is the (e.g., 2kW, 3kW, or 4kW), and what are the busy peak hours for hot water in your household? Share public link
Provides a 1-hour manual bypass to heat water instantly. Note that this override is typically disabled during designated peak load times to prevent grid strain. LED Status Lights: Green: Mains power is connected. Red: Geyser is currently ON .
Disclaimer: High-voltage work can be dangerous. Installation must be performed by a qualified electrician or under strict safety guidelines. Always switch off the main DB power supply first. Prerequisites KES ISG1201 Go to product viewer dialog for this item. Timer Unit Flat screwdriver Appropriate wire cutters/strippers DIN Rail space in the DB Board
If your geyser element exceeds 4000W or the timer’s rated current limit, install a heavy-duty electrical contactor alongside the timer. The timer will switch the contactor coil, and the contactor will safely handle the high current load of the geyser. Troubleshooting Common Issues
If you need water urgently, use the manual override outside of peak hours. For long-term savings, ensure your geyser thermostat is set between 55°C and 60°C .
Press the MANUAL override button until the screen explicitly reads . Schedules trigger at the wrong times
Toggles the operational state between permanent ON, permanent OFF, or scheduled AUTO modes.
Snap the KES timer securely onto the DIN rail and close the distribution board safety panel. 3. Interface Overview and Button Functions
This guide serves as a manual for the "Kes geyser load control timer new," offering a detailed breakdown of its features, programming, installation, and troubleshooting to ensure you can harness its full potential.
Nina smiled. She taped the inside the meter box, right next to the silent, obedient unit.
Press the button to adjust the exact minute for activation. Programming Schedule 1 (OFF Cycle)
Always switch off the main electrical supply at the circuit breaker before touching any wiring. Verify the power is off using a reliable voltage tester.
Connect the incoming from the main neutral bar to Terminal 2 (Input N) on the timer.
While holding the Clock button, press to adjust the current hour.
Verify that the screen displays the word AUTO . Press P to check your schedules and confirm that the days selected for "1_ON" are identical to the days selected for "1_OFF" .
Once your schedules are entered, press the button to save and exit to the main screen. How to Modify or Delete a Single Program
Connect a wire from on the timer to the neutral input side of the geyser isolator switch.
The KES ISG1201 includes four factory-set profiles. To select a program, use the button to cycle through them. Blue LED Pattern Function & Operating Hours Prog 1 1 flash / second
X-link Azərbaycanın aparıcı internet təchizatçısıdır. Statistikalarımızla tanış olun.